INOX-MX3 for Electrical & Electronics

Inox lubricant is a very versatile, high quality product in it’s application for the lubrication & protection from corrosion & moisture for all electrical and electronic parts & equipment.

Inox is non-staining, non-corrosive, non-static and non-conductive, but does not effect the current flow when used in any electrical or electronic switches, plugs, circuits, fittings, parts or equipment.

Electrical

SWITCHES, PLUGS AND LIGHT FITTINGS

Use INOX lubricant to penetrate corrosion and free up switches, bayonet & screw socket light globes, all light fittings, plugs & cable couplings, keeps this type of equipment corrosion free and in good serviceable order for up to 2 years. Spray INOX on screw socket type light fittings, it stops corrosion and makes globes easier to unscrew when replacing, Use INOX to protect against moisture and corrosion, refrigeration unit circuits & cable connectors & plugs used in sea, road and rail containers. Helps prevent short circuit arcing and earth leakage.

RELAYS, SOLENOIDS AND REGULATORS

Use INOX to keep relay, solenoid and regulator coils & circuits, contact arms & pivots lubricated and free from corrosion. INOX is very effective in stopping condensation in this type of equipment used cold storage rooms, freezing works, abattoirs, etc, dramatically reducing instances of short circuits and seizures caused by moisture and corrosion.

MOTORS, GENERATORS AND POWER BOARDS

INOX can be safely spray on field windings & armatures in motors and generators to protect them from moisture and corrosion, lubricates shaft bushes and small pin & ball bearings, helps prevents grounding and seizing. For protection from moisture and corrosion caused by condensation, spray INOX into cold room fan motors and exhaust fan motors used in high moisture areas. Use INOX on power board circuits as a preventive measure against moisture and corrosion, keeps power board relays and solenoids in good operating condition, free from moisture and corrosion.

CAUTION: INOX can be safely used on all direct, single and multi phase alternating and high tension currents with the one (1) exception, when using the Aerosol Packaged INOX, please allow a couple of minutes for the propellant gas to dissipate before switching on the current. This procedure is not required for the non-pressurized packaged INOX. INOX can be readily removed with most mineral based solvents.

Electronics

CIRCUITS, MULTI-PIN PLUGS AND KEY BOARDS

INOX frees up sticking computer and word processing equipment key board keys, keeps them free and in a smooth operating condition. Spray INOX into multi-pin sockets and on multi-pin plugs for protection from corrosion and electrolysis caused by condensation, stops plugs sticking and jamming in. INOX keeps circuits free from moisture and corrosion, stops electrolysis.

CAUTION: Do not use INOX on Recording Heads or Bladder switches (It may effect the operating efficiency of these parts).

VALVES, MICRO-SWITCHES AND VARIABLE CONDENSERS

INOX will remove static caused by condensation and corrosion in variable condensers ( allow up to 48 hours to take effect) and tuners, frees up micro-switches and make them fully functional again. Stops electrolysis and corrosion on valve contact pins and always keeps them easy to remove and replace.

THE MELBOURNE WIRELESS AND SOUND MUSEUM

“In our restoration of vintage electronic & mechanical equipment we use the product INOX. We have found that this product gives superior protection to the electrical wiring, tuning capacitors, power transformers, loud speaker assemblies and chassis.As this product is non-conductive and does not become sticky or cause discolouration, we use it to stop the effects of electrolysis on copper windings. In our experience as the paper insulation between the windings deteriorates and acid is produced which if left untreated will destroy the device. As these components can no longer be produced we rely heavily on the protective properties of INOX. After extensive testing of many penetrating, anti-corrosion and lubricating products, we now use INOX exclusively in all restoration work undertaken by this department”. Chief Engineer – Restoration Department.

TELEPHONE SYSTEMS

INOX lubricant stops electrolysis between aluminium and stainless steel, keeps fibre optics cable connectors corrosion and moisture free. INOX keeps relays, contact assemblies, circuits and wiring terminals used in telephone hand sets, switch boards and telephone exchanges moisture and corrosion free.

RADIOS, TELEVISIONS AND ANTENNAS

In high moisture and coastal areas, INOX will protect radio and television receiver circuits & chassis from moisture and corrosion. INOX protects marine two way radios and other marine electronic equipment from electrolysis and corrosion caused by salt air and condensation, can be sprayed directly into electronic equipment. Use INOX to protect cable terminals on TV antennas and satellite receivers from corrosion.

Inox lubricant can be used for protection against electrolysis, corrosion and condensation for all electrical & electronic circuits, parts and equipment.

Caution: Inox may effect some natural rubber products with continual long term use.